KINTEC RACING
Precision Perfomance Products
Plasti Dip Liquid Spray Clear A great way to waterproof your receivers. Just cover the connector pins and spray directly on the receiver board for a waterproof seal. This is a must have for boats.
Can only be shipped to US customers. $7.50 per can
Plasti Dip Liquid Electrical Tape Liquid Tape is an air dry synthetic rubber coating that can be easily applied and exhibits excellent moisture, acid, alkaline, abrasion and dielectric resistance. Will not crack, peel, or harden. Remains flexible even under extreme conditions. Brush on cap. Can only ship to US customers.
4oz bottle for $7.50
CorrosionX Aerosol or Liquid for Overseas Customers A great way to water proof your electrical components. Provides long-term protection against rust and corrosion on any metal surface.
Available in 6oz aerosol for $8.75 or 4oz liquid for $6.95. Only liquid can be shipped out side the US.
Soldering Jig Anodized aluminum soldering jig with non skid feet on the bottom. Holds most connectors such as Deans, Traxxas, XT60, Micro Deans, EC3, EC5. A variety of bullets such as 3.5mm, 4mm, 5.5mm. $20.00
KV-RPM Meter Check your motors actual kv and rpm under load or no load. Also checks voltage at the same time. Very easy to use and easy to read instructions. No hard wiring required using the provided alligator clips. $25.00
Hyperion EOS Sentry - Lipo/Battery Pack Checker
- LiPo, LiIon and LiFe from 2S to 7S
- NiCd and NiMH from 4 to 7 cells
- Large clear display
It can be used with the most common battery types used for RC modeling.
For Lithium based types (LiPo, LiIon, and LiFe), it will work with pack sizes of 2S to 7S and for NiCd and NiMH packs it supports 4 to 7 cells.
Futaba BR-3000 Battery Checker Checks the state of the following battery packs. 2-7 cell LiFe, LiPo and Li-Ion packs. 4-7 cell NiCd and NiMH packs. Battery pack total voltage display and remaining capacity are displayed on a bar graph and in percent. Voltage of each cell of a lithium battery pack can also be displayed. Operates on the power supplied from the connected battery. One year limited warranty through Hobby Services beginning at date of purchase. $50.00
Programing Card For Seaking ESC's
Lipo Monitor 2-6s An excellent easy way to check the voltage of your packs. This unit checks the voltage of each cell and then the total of the pack. Simple to use just plug into the balancing tap. Only $5.00
Low Voltage Alarm 2s-4s Made for on board use. Plugs into balance lead to detect low voltage on any cell. If any cell drops below 3.3v a very loud alarm will sound and the green lights change from green to red. Very handy lightweight unit. $3.75
DC Voltage Booster This little unit will boost the voltage of a single cell lipo to 5 volts allowing you to run receiver and servos. Replace those AA batteries and save some weight. Input range 3.2v-4.2v (1S Lipo) $6.00
Zippy Flightmax single cell 1s1p, 3.7v, 400mAh, 30c/40c, Has a JST connection installed, 13.2grams, 63x26x4mm. $7.00
Castle Creations BEC Eliminates the need for a receiver and servo battery pack. Draws higher voltage from the motor batteries and drops it to a voltage level suitable for the receiver and servos.
Input voltage: 5V to 25.2V (2S to 6S LiPo)
Current output: 12 volts input = 7 amps* continuous, 10 amp peak;
24 volts input = 5 amps* continuous, 7 amp peak
*Ratings are determined with a 5mph airflow on the BEC
Selectable Output: 4.8 - 9.0V via the Castle Link (sold separately)
Default voltage is 5.1V
Very High Voltage BEC Dimension Engineering's Very High Voltage BEC is the world's first BEC compatible with input voltages as high as 60V/14s lithium. It can power your receiver and servos with up to 2.5A. VHVBEC's output is selectable between 5V/6V using a small slide switch. The 6V setting gives more speed and torque to the servos. VHVBEC is targeted towards customers who will be running packs 8s and larger.
Input voltage: 9V to 60V (3s-14s lithium, up to 40 cell NiMH)
Output current: 2.5A (~6 standard servos, 4 digital)
Weight: 17g/.6oz (including wires)
Universal connector fits all receivers
Sport BEC SportBEC powers your receiver and servos much more efficiently than a standard BEC. SportBEC works great up to very high voltages. SportBEC is usually a necessity at 4s and above when running high torque or digital servos. SportBEC's output is selectable between 5V/6V using a small slide switch. The 6V setting gives more speed and torque to the servos. Because it is an efficient switching regulator, SportBEC can supply its full rated current of 3.5A all the way up to 8s.
Input voltage: 9V to 33.6v (3s-8s lithium, up to 21 NiMHs)
Output current: 3.5A (~8 standard servos, 4-6 digital)
Weight: 13g/.46oz (including wires)
Universal connector fits all receivers
Park BEC Dimension Engineering's ParkBEC is the smallest and lightest switch-mode BEC on the market. ParkBEC powers your receiver and servos much more efficiently than a standard BEC. The ParkBEC installs between your ESC and receiver.
Input voltage: 6V to 33.6v (2s-8s lithium, up to 21 NiMHs)
Output current: 1.25A continuous, 1.5A 60 second peak. (6 4-9g servos, 4 standard servos)
Weight: 6.2g/.22oz
Universal connector fits all receivers
LipoShield Intelligent Lithium Cutoff, 1-12s, Soft cutoff. Works with all ESCs. These have been reprogrammed to cutoff at 3.3volt per cell. Now you can run lipos in your supervee with the stock ESC and not damage or shorten the life of your lipos. Just run till the cutoff kicks in, go to zero throttle and bring her in. No more need for a stop watch or worrying how much juice you have left. For the price this is a must have if you are running lipos. A great backup for any ESC. If you cant solder get the preinstalled deans option. This also gives you the ability to move the unit from one boat to another. Made in USA
Pico Switch radio controlled relay PicoSwitch is a relay switch that you toggle via your radio. Quickly and easily control anything from a water pump or digital camera shutter or an electric squirt gun or lighting and more. You can activate applications with voltage levels as high as 125VAC. PicoSwitch plugs into a standard hobby radio control receiver. You connect the load that you want to toggle using PicoSwitch's wear resistant screw terminals.
Specifications:
Max relay voltage: 60VDC, 125VAC
Max relay current: 1A @ 24VDC, 0.5A @ 125VAC (60W lightbulb)
Relay resistance: 100 mΩ max
3.5V to 5.5V operating voltage
30mA typical draw from receiver $20.00
BattleSwitch radio controlled 10Amp relay. BattleSwitch is the larger, 10A version of our popular Picoswitch.
You can use BattleSwitch to quickly and easily control glow plugs, BattleBot weaponry and more. You can activate applications with voltage levels as high as 240VAC. BattleSwitch plugs into a standard hobby radio control receiver. You connect the load that you want to toggle using BattleSwitch's wear resistant screw terminals.
Specifications:
Max relay voltage: 240VAC
Max relay current: 10A @ 28VDC, 12A @ 120VAC, 10A @ 240VAC
Relay resistance: 100 mΩ max
3.5V to 5.5V operating voltage (on servo pigtail)
30mA typical draw from receiver $25.00
Vinyl Safety Caps for 5.5 male bullets Perfect for protecting the 5.5mm male bullet. Nice snug fit yet easy on and easy off. The best I have found. 10pcs for $1.00 or 100pcs for $7.00
Vinyl Safety Caps for 5.5 female bullets Perfect for keeping debris from getting into the female bullet. Fits over the bullet with shrink wrap. Nice snug fit and easy to remove. 10pcs for $1.75 or 100pcs for $15.00
8mm Male Vinyl Safety Caps Perfect for protecting the 8mm male bullet. Nice snug fit yet easy on and easy off.
10 caps for $1.00 or 100 caps for $7.50
Safety Caps Reusable rubber caps that keeps your bullet connectors from arcing to each other or any other metal object. Fits over any size bullet connector or heavy gauge wire.
Approx 1 3/4 long. .75 cents per pair, or 16 caps for $5.00.
14 Gauge AWG Multi strand 14 gauge silicone wire. Very flexible and easy to work with. sometimes called wet noodle. Great for cramming in tight spots. Sold by the foot
12 Gauge AWG Multi strand 12 gauge silicone wire. Very flexible and easy to work with. Sometimes called wet noodle. Great for cramming in tight spots. Sold by the foot.
10 Gauge AWG Multi strand 10 gauge silicone wire. Very flexible and easy to work with. sometimes called wet noodle. Perfect for upgrading any esc. Great for cramming in tight spots. sold by the foot
8 Gauge AWG Multi strand 8 gauge silicone wire. Sometimes called wet noodle. Very flexible yet strong. Allows for cramming into tight spots without kinking. For 5.5mm bullet connectors and up. Great for any esc. sold by the foot.
Twisted Wire Protector Perfect for protecting and bundling servo wires. 6mm diameter. Can be died any color.
Sold in 3 foot lengths for 50cents.
6mm Heat Shrink Tubing Works with 3.5mm up to 5.5mm bullet connectors. Is snug on 5.5mm connectors.
7mm Heat Shrink Tubing Perfect size for 5.5mm bullet connectors. .50 cents per foot
10mm Heat Shrink Tubing Works with 5.5 bullet connectors and larger. .50cents per foot.
Futaba 3 inch Servo Extension Gives you 3 more inchs of length from servo or esc to reciever. Has standard J connector.
Futaba 8 inch Heavy Duty Extension Gives 8 inches more length from servo or esc to receiver. Has standard J connectors one male and one femal. Made with heavy 20 gauge wire for higher current loads.
Servo Extension 16" inch long (42cm) servo extension with one female and one male connector.
Hitec Heavy Duty Y Harness 6 inch length with Hitec S, JR, Airtronics Z Connectors. Heavier, 20-gauge wire handles higher current loads. Great for connecting 2 esc's to one radio. $10.30
Eagle Tree E-Logger V4 150amp w/ wire leads This is the 150 amp e-Logger V4 On-Board Data Logger from Eagle Tree Systems.
Accepts optional inexpensive sensors for GPS, temperature, RPM (brushless, magnetic or optical) airspeed, altitude, servo current and more.
Logs throttle movement with optional Y-cable.
Current measured with a true Hall Effects sensor-not a resistance shunt that creates heat and robs power from the system.
Fully compatible with Windows Vista, 98SE, ME, Win2K and XP.
USB live mode support displays info from the model live on the bench on modeler's PC.
All data is logged to permanent memory, which retains data even when power is removed, adjustable logging rate (1-10 samples/second) and lossless data compression for long log times.
State of the art Windows virtual playback display and graphing.
Internet updatable firmware.
One year limited warranty.
INCLUDES: 150 amp e-Logger V4 On-Board Data Logger, USB cable, and CD manual.
Eagle Tree GPS V4 Expander This is the 10Hz GPS V4 Expander Module for the Eagle Tree Data Recorder and V3 eLogger. Must fast then the previous model.
For use in either RC vehicles or aircraft, this module allows modelers to log vehicle position, visualize model on a 3D graph against a photo image of field or track and see position of model on the Seagull Dashboard screen. Google Earth software allows data to be easily and fully visualized.
3D position graphing in the Virtual Dashboard software with support for overlayed images of field or track. Latitude/longitude, GPS speed, GPS altitude, course, distance to operator and UTC timestamp.
10Hz GPS Expander Module with 4-pin connector and instruction sheet.
One year limited warranty through mannufacturer beginning at date of purchase. $72.00
Eagle Tree Optical RPM Sensor This is the Optical RPM Sensor for use with the Data Recorder and MicroPower V2. Pre-Soldered to Wire. $13.80
Eagle Tree Micro Temperature Sensor for use with the Eagle Tree Data Recorder and MicroPower V2. Pre-Soldered to Wire $9.50
Eagle Tree Power Panel LCD Display Perfect for on site data viewing. No need to drag the PC along anymore.
Ultra thin LCD display connects to the MicroPower E-logger.
Live display of amps, volts, mAh, temperatures and RPM.
Cumulative mAh display for battery pack lets modeler know approximately how much time is left.
Up to four paramenters can be displayed, each parameter has programmable label.
Multiple "virtual pages" of data are supported, programmable switching between pages.
Supports display of Live Data and Max values, programmable switching.
Supports both metric and english units. One year limited warranty. $35.00
Deans Charging / Balancing Board Charge six (2~6S) lipo packs with same capacity & cell count simultaneously at the same time with a standard charger with this parallel charging board. The balancing taps are JST-XH type such as used on Zippy and Turnigy lipos. Has a max current of 30amps. $15.00
XT60 Charging Board Charge six (2~6S) lipo packs with same capacity & cell count simultaneously at the same time with a standard charger with this parallel charging board. The balancing taps are JST-XH type such as used on Zippy and Turnigy lipos. Has a max current of 30amps. $15.00
Rubycon Capacitor Voltage Rating: 25VDC Capacitance: 1500µF Capacitor Type: High Temperature. Great for the UL-1
This little unit is great added extra insurance for your ESC. Also if you have puffed a cap just install this instead of replacing the esc. Very easy to install. Solder the +pos (long wire) to the red wire and the -neg to the black wire and your done. Add as many as you like. If you are already planing on a shipping charge I highly recommend one. $0.75 ea
Rubycon Capacitor Voltage Rating 25VDC Capacitance: 1000uF Type: High Temp
Rubycon Capacitor Voltage Rating: 35VDC Capacitance: 1000uF Type: High Temp Seaking 180 replacement
$0.75 each
Rubycon Capacitor Voltage Rating: 35VDC Capacitance: 560 Type: High Temperature Castle replacement
Rubycon Capacitor Voltage Rating: 35vDC Capacitance: 390uf Type: High Temperature Castle replacement
Castle Creations - Castle Link Quick Connect Installs between ESC and receiver. Y-harness with wire to connect to Castle Link. Can leave connected for easy access for Castle Link without disrupting receiver or ESC. Detects the presence of Castle Link adapter.
Castle Creations - Castle Link USB Programming Kit Adapter for PC Interface with Hydro, Phoenix, Mamba, Barracuda, Phoenix HV and Thunderbird Brushless controllers View, change and customize program options Update ESC software via the Internet Compatible with Windows XP and Vista (32 and 64 bit) USB port required.
Hobbico Soldering Iron 60 Watt Comes with 2 flat chisel tips and a table stand. Very affordable. $8.00
Novak Lead Free Silver Solder Rosin Core Solder. Specially formulated for hand soldering. Contains 3% silver for high-conductivity, low-resistance and strong solder joints at a relatively low melting point. 15grams $8.60
Novak Lead Free Silver Solder Rosin Core Solder. Specially formulated for hand soldering. Contains 3% silver for high-conductivity, low-resistance and strong solder joints at a relatively low melting point. 100grams $38.00
TrakPower TK-950 Soldering Station Heavy-duty 60 watt design. Heats quickly to selected temperature within a range of 392°-896°F. Holds setting within 1.8°F when idle. 5-year warranty on unit, 1 year warranty on iron handle's electronics. Includes Soldering iron with stand, sponge, temperature control unit, chisel point tip, pencil tip, instruction manual and decals. One of the best on the market and worth every penny. $80.00
Demo Video
Watt's Up Meter From RC Electronics. High resolution on all measurement ranges to accurately check battery pack cell balance and measure single cell packs. Sets cutoff currents and voltages, compares components and detects wear prior to component's failure. Measures eight essential electrical values.
Captures Peak Amps, Peak Watts and Minimum Volts events.
Current: 0-100A Peak, 50A Continuous, .01A Resolution.
Charge: 0-65535mAh, 1mAh resolution.
Power: 0-6500 Watts, .1W Resolution.
Voltage: 4-60V, .01 Resolution.
Energy: 0-6500 Watt Hours, .1Wh resolution.
Powered by circuit-no battery to change, 16 character, 2 row LCD display.
Length: 2.8" (71mm), Width: 1.7" (43mm), Height: .83" (21mm), Weight: 2.3oz (65g)
