KINTEC RACING
Precision Perfomance Products
4mm Adjustable Stinger Hard anodized aluminum. Teflon bearings installed. Distance from transom to end is 73mm. Mounting bracket is 19mm wide x 30mm high. $18.00
4mm Teflon Bushings Replacement bushings for 4mm shaft strut. 2pcs for $2.50
Sm 3/16 Adjustable Stinger Hard anodized aluminum. Made to slide over stuffing tube and use sv/ul-1 bushing
Distance from transom to end 2 7/8 inches. Mounting bracket is 3/4 wide x 1 3/16 high.
3/16 Adjustable Stinger Anodized aluminum. Has 2 Teflon bushings installed. Fits 3/16 shaft.
Distance from transom to end is 2.56 inch (65mm)
Transom foot print is 1.25 inch (32mm) wide and 1.57 inch (40mm) high. $24.00
3/16 Adjustable Stinger Anodized aluminum. Has 2 Teflon bushing installed. Fits 3/16 shaft. $36.00
Distance from transom to end is 3 1/16inch (78mm)
Transom foot print is 1.30 inch (33mm) wide and 1 1/2 inch (38mm) high.
1/4 Adjustable Stinger w/ Roller Bearings Anodized aluminum. Has two roller bearings installed. Grease fitting located between the two. $44.00
Distance from transom to end is 3.35 inch (85mm)
Transom foot print is 1.80 inch (46mm) wide and 1.97 inch (50mm) high.
1/4 teflon bushings Bushings for 1/4 shafts. Sold in pairs for $2.50
3/16 Small Strut Has 3/16 teflon bushings for 3/16 shaft. $30.00
Top of bracket to bottom of strut adjustable from 2.05" to 1.83" (52mm-46.5mm)
Length from transom to rear of strut adjustable from 1.5" to 1.97" (38mm-50mm)
Transom footprint is 1 inch wide and .78" high (25mm x 20mm)
3/16 Small Strut This is machined for 3/16 shaft and uses the Aquacraft brass bushing. Adjustable horizontally and vertically. Measurement from transom to rear of strut is 1 1/2 inches to 2 inches. Height measurement from bottom of bracket to shaft centerline is 7/8 to 1 1/8. Hard anodized aluminum with all stainless mounting screws, washers and nuts included. Bushing included.
4MM Small Strut Has 4mm teflon bearings installed for 4mm shaft. $16.00
Top of bracket to bottom of strut adjustable from 52mm to 46.5mm (2.05" to 1.83")
Length from transom to rear of strut adjustable from 38mm to 50mm (1.5" to 1.97")
Transom footprint is 25mm wide and 20mm high (1" x .78")
4mm Strut Anodized aluminum adjustable strut with 4mm teflon bushings installed.
Top of bracket to bottom of strut adjustable from 1.7-2.2 inch (43mm-55.8mm)
Length from transom to rear of strut 1.18 inch (30mm)
Transom foot print is .98 wide and .87 high (25mm x 22mm) $12.00
3/16 Strut Aluminum adjustable strut for 3/16 shaft with teflon bearings installed.
2 3/8 (60mm) from top of bracket to bottom of strut.
2 inch (50mm) length from transom to rear of strut. machined to fit 1/4 stuffing tube. All stainless cap screws, washers and nuts needed included. $21.75
3/16 Teflon Bushings Replacement bushings for struts and stingers. 2 pcs for $2.50
1/8 Strut Anodized aluminum. Fits 1/8 shaft. Compact and strong strut. $13.00
Distance from transom to end is 1 1/4 inch (32mm)
Transom foot print is .93 inch (24mm) wide and .43 inch (11mm) high.
1 1/2 Inch Micro Rudder w/ water pickup Hard anodized aluminum machined rudder with water pickup and linkage arm which can be mounted from either side.
1 1/2 inch (38mm) blade length from bottom of bracket to rudder tip.
.835 inch (21.2mm) from transom to leading edge of rudder.
Transom foot print is 5/8" (17mm) wide and 1/2" (13mm) high. $14.00
2 3/16 Inch Center Mount Rudder Powder coated machined aluminum rudder. Mounting bracket is center mount type. Rudder has dual side linkage arm and brass shear bolt for kick back protection.
2 3/16 inch (56mm) blade length from bottom of bracket to rudder tip.
5/8 inch (16mm) from transom to leading edge of rudder.
Transom foot print is 5/8" (17mm) wide and 1/2" (12mm) high. $18.00
Nylon Breakaway Bolts Used for 2 3/16 rudder above. 2mm x 8mm. 5pcs for $1.00
2 1/4 Inch Rudder w/ water pickup Aluminum hard anodized machined rudder with water pickup.
2 1/4 inch (57mm) blade length from bottom of bracket to tip.
1 5/8 inch (42mm) from transom to leading edge of rudder.
Transom foot print is 1/2" (13.5mm) wide and 7/8" (23mm) high.
Adjustable linkage can be mounted on either side. Breakaway aluminum bottom bolt but I recommend this be replaced with 3x10 nylon breakaway bolt to prevent damaging threads. Looks much better then the picture. $15.00
2 7/8 Inch Center Mount Rudder Powder coated machined aluminum rudder. Mounting bracket is center mount type. Rudder has dual side linkage arm and aluminum shear bolt for kick back protection.
2 7/8 inch (74mm) blade length from bottom of bracket to rudder tip.
1 inch (25mm) from transom to leading edge of rudder.
Transom foot print is 7/8" (22mm) wide and 5/8" (16mm) high. $20.00
3 inch Rudder w/ water pickup Aluminum hard anodized machined rudder with water pickup.
3 inch (75mm) blade length from bottom of bracket to tip.
1 5/8 inch (42mm) from transom to leading edge of rudder.
Transom foot print is 1/2" (13.5mm) wide and 7/8" (23mm) high.
Adjustable linkage can be mounted on either side. Breakaway aluminum bottom bolt but I recommend this be replaced with 3x10 nylon breakaway bolt to prevent damaging threads. Looks much better then the picture. $15.00
Nylon Shear Bolts For 2 1/4" and 3" Rudder These are much easer on the rudder then the provided aluminum bolt. 3mm x 10mm. 5pcs for $1.00
4 inch Rudder w/ water pickup CNC machined aluminum, silver anodized rudder and mounting bracket with water pickup and servo arm. Notched for kick back protection.
4 inch (102mm) from bottom of mounting bracket to rudder tip.
3 1/4 inch (83mm) from transom to leading edge of rudder.
Transom foot print is 1.1" (28mm) wide and 1.1" (28mm) high.
Rudder width tapers from 1 inch to 3/4. Servo arm can be mounted from either side. All stainless steel locknuts, bolts and washers included. $27.00 each
5 Inch Rudder Short Base w/ Dual Water Pickup CNC machined aluminum rudder and mounting bracket with dual water pickups and servo arm. Brass bolt for kickback protection.
5 inch (128mm) from bottom of mounting bracket to rudder tip.
1 1/2 inch (38mm) from transom to leading edge of rudder.
Transom foot print is 1.7" (43.4mm) wide and 1.26" (32mm) high.
Rudder width tapers from 1 1/4 inch to 1.1
Servo arm w/ 2mm swivel. All stainless steel locknuts, bolts and washers included.
5 inch Rudder Offset Base w/ Dual water pickup CNC machined aluminum rudder and mounting bracket with dual water pickups and servo arm. Brass bolt for kickback protection.
5 inch (128mm) from bottom of mounting bracket to rudder tip.
3 5/8 inch (94mm) from transom to leading edge of rudder.
Transom foot print is 1.7" (43.4mm) wide and 1.26" (32mm) high.
Rudder width tapers from 1 1/4 inch to 1.1
Servo arm w/ 2mm swivel. All stainless steel locknuts, bolts and washers included. $27.00 each
5 inch Rudder Extended Bracket, Centered base, w/Dual Water Pickup Powder coated aluminum 5inch rudder with dual water pickups. Extended length bracket. Has brass shear bolt for kick back protection. Includes linkage arm with swivel.
Rudder length from bottom of bracket to tip is 5 inch (127mm)
Length from transom to leading edge is 6 1/4 inch (156mm)
Rudder width is 1 1/4 inch (31.5mm)
Transom foot print is 1 5/8 (42mm) wide and 1 1/4 (32mm) high $56.00
5 1/2 inch Rudder, Centered Base w/ water pickup. Hard anodized aluminum 5 1/2 inch rudder with water pickup on each side. Has a brass shear bolt for kick back protection. Includes linkage arm and 2mm swivel.
Rudder length from bottom of bracket to tip is 5 1/2 inch (140mm)
Length from Transom to leading edge is 3 7/8" (99mm)
Rudder width is tapered from 1.34" (34mm) to 1.1" (28mm)
Transom foot print is 1.65" (42mm) wide and 1.26" (32mm) high $35.00
4 Inch Short Base Cat Rudder Hard anodized aluminum rudder with water pickup and shear bolt break away type. Has a pull-pull type linkage arm. Short base that sets the rudder 1.1 inch (28mm) from the transom.
Transom foot print is 1.1 wide and 7/8 inch high (28mm x 22mm) $30.00
4mm Cat Strut Adjustable aluminum strut. Has a 4mm square socket shaft with bullet nut and stainless drive dog. Comes in both left and right drives.
The strut is 80mm from transom to end.
Footprint is 25mm (1") high and 24mm (.95") wide $20.00ea
3/16 Adjustable Cat Strut Comes with a 3/16 square socket solid shaft with stainless bulletnut and stainless drive dog. Can be used for right or left hand drive. $30.00 each
Strut length from transom to end not counting shaft is 110mm or (4 5/16")
Transom foot print is 25.6mm high (1") and 23.5mm wide (.93")
3 5/8 Inch Cat Rudder and 3/16 strut w/ water pickup. Anodized aluminum rudder strut combo. Rudder has water pickup and break away bolt. Dual servo arm with linkage pivot. Mounting bolts included.
3 5/8 inch (92mm) from bottom of bracket to rudder tip.
2 3/4 inch (70mm) from transom to leading edge of rudder.
Transom foot print is 1 1/8" (30mm) wide and 1 inch (25mm) high.
1 1/4 strut center line to bottom of bracket. Made for 3/16 shaft. $28.00
3 5/8 Inch Cat Rudder and 4mm strut w/ water pickup. Anodized aluminum rudder strut combo. Rudder has water pickup and break away bolt. Dual servo arm with linkage pivot. Mounting bolts included.
3 5/8 inch (92mm) from bottom of bracket to rudder tip.
2 3/4 inch (70mm) from transom to leading edge of rudder.
Transom foot print is 1 1/8" (30mm) wide and 1 inch (25mm) high.
1 1/4 strut center line to bottom of bracket. Made for 4mm shaft. $28.00
1 1/8 Trim Tabs Type 1 1/8 wide (29mm), 1 1/2 from transom to tip (40mm), 5/8 high (16mm). CNC machined silver anodized aluminum adjusters with stainless tabs and all stainless mounting hardware included. $12.00 per pair
1 1/2 Trim Tabs 1 1/2 wide (38mm), 1 1/4 from transom to tip (31mm), 3/8 high (10mm). CNC machined silver anodized aluminum adjusters with stainless tabs and all stainless mounting hardware included. $12.00 per pair
1 1/2 Trim Tabs Long Version 1 1/2 wide (38mm), 2 inch from transom to tip (50mm), 9/16 high (15.5mm). CNC machined silver anodized aluminum adjusters with stainless tabs and all stainless mounting hardware included. Also available with water pickup. $12.00 per pair or $22.00 with water pickup up.
2 1/4 Dual Trim Tabs 2 1/4 wide (57mm), 1 7/8 from transom (46mm), 5/8 high (17mm). Beautifully machined silver anodized aluminum adjusters with stainless tabs and all stainless mounting and adjusting hardware included. Dual split tab makes for better fine tuning. $12.00 per set.
3" Dual Trim Tabs 3" wide (76mm), 1.9" from transom (50mm), 5/8" high (17mm).
Beautifully machined silver anodized aluminum adjusters with stainless tabs and all stainless mounting and adjusting hardware included. Dual split tab makes for better fine tuning. $20.00 per set
1/4 K&S Brass Tube #131 Perfect for stuffing tube when using .150 flex and Teflon. Sold in 1 foot lengths.
