Dubro 2-56 Threaded Rod #172   .072 diameter rod 12inches long threaded 2-56 on one end.  $1.00ea
 

Du-Bro 2-56 Fully Threaded Rod 12"   Stainless steel rod threaded 2-56 end to end. .072 diameter. 12 inches long.   $1.50 ea

GreatPlanes Solder Clevis 2-56    For soldering on the smooth end of .074 rod.  Nickel plated.     $1.25 per pair

Great Planes 2-56 Threaded Clevis  Perfect for attaching rod to servo horns. Comes in pack of 2.  $1.30 per pack
 

Dubro Safety Lock Kwik Link 2-56  Brass plated stepped steel pin does not bind on control horns and has a large flat head for easy removal. Safety lock is mounted in a track system on the clevis body to prevent it from being lost. 10% lighter than a steel clevis.
Sold in pairs for $2.10

Dubro 2-56 Swivel Ball Links  Complete with all hardware needed. 2 per pack.  $3.50
 

Dubro Swivel Connector 2-56   Great way to connect pushrod to servo. Pivots for no binding.  Adjustable on the rod with a set screw.  Works on 2-56 and smaller rod.  $1.90 per pair

Dubro 4-40 Threaded Rod #144  .093 diameter rod 12 inches long, threaded 4-40 on one end. $1.00ea

Du-Bro 4-40 Fully Threaded Rod  Stainless steel rod threaded 4-40 end to end. .093diameter. 12 inches long.  $1.75 each.

Dubro 4-40 Turnbuckles w/ Wrench  These have a right hand thread on one end and left hand end on the other. Makes fine tuning of length easy with just the turn of the wrench. Length of rod is 2 5/8 with 1 1/8 of thread on each end. Plenty of thread to cut to desired length.  Sold in pairs with wrench included.  $3.90
 

Great Planes 4-40 Threaded Clevis Perfect for attaching rod to servo horns. Comes in pack of 2.   $1.50 per pack
 

GreatPlanes Solder Clevis 4-40  For soldering on the smooth end of .095 rod. Nickel Plated  $1.80 per pair
 

Dubro Safety Lock Kwik Link 4-40  Brass plated stepped steel pin does not bind on control horns and has a large flat head for easy removal. Safety lock is mounted in a track system on the clevis body to prevent it from being lost. 10% lighter than a steel clevis.
Sold in pairs for $2.10
 

Dubro 4-40 Swivel Ball Links Complete with all hardware needed. 2 per pack.   $3.50 per pack
 

Dubro Swivel Connector 4-40 Great way to connect pushrod to servo. Pivots for no binding. Adjustable on the rod with a set screw. Works on 4-40 and smaller rod.  $2.20 per pair
 

Sullivan Heavy Duty Steel Pushrod Connector  Fits 2-56 and 4-40 rods. Uses a washer and nut for retainer on servo or linkage arm.  $2.40 ea
 

Dubro Swivel Ball Link 4-40/2-56  These are for using a 4-40 rod but come with smaller 2-56 hold down screw and pivot.
 

Dubro 2mm Swivel Ball Links  Complete with all hardware needed. 2 per pack.  $3.50 per pack
 

Dubro Safety Lock Kwik Link 2mm  Brass plated stepped steel pin does not bind on control horns and has a large flat head for easy removal. Safety lock is mounted in a track system on the clevis body to prevent it from being lost. 10% lighter than a steel clevis.
Sold in pairs for $2.10
 

Du-Bro Push Rod Seals   For 2-56 or 4-40 rods. Allows for a full inch of travel. 2 per pack.   $3.90

Bru Line Pushrod Seals w/ Hardware  For 2-56 or 4-40 rods. Water and fuel proof.  $4.80 per pair.

Bru Line Replacement Pushrod Seal   Replacement boots for Bru Line Brub2100.  These work great with 3/8 brass or aluminum tubing.  $3.70 per pair
 

AquaCraft Radio Box Seal Boot    Fits 2-56 or 4-40 rods.  Works perfect over 3/8 brass on aluminum tubing.   $2.70 per pair

Venom Push Rod Seals   Fits both 2-56 or 4-40 rods.  $5.00 per pair
  

Small Push Rod Seals   Fits both 2-56 and 4-40 push rods. These can be glued back to back, one inside and one out side for a perfect seal.  Overall length is 1.10 inch (28mm).  Use 7/16 drill.  Made in USA. $6.00 per pair.

Medium Push Rod Seals  Fits both 2-56 and 4-40 push rods. Overall length is 1.34 inch (40mm). Use 1/4 drill. $2.50 per pair.

Large Push Rod Seals  Fits both 2-56 and 4-40 push rods. Overall length is 1.66 inch (42.2mm) Use 5/16 drill. $2.50 per pair.

DuBro E/Z Bender Wire forming tool. Works on .062" - .093" (1.6mm -2.4mm) diameter wire. Will bend wire from 0-90 degrees. Makes perfect Z-bends, L-bends in linkage.  $22.50

K&S 2-56 Threading Die  Fits 3/4 inch die handles. Adjustable die. When cutting threads do not try to cut in one pass. Adjust the die to is largest size for first pass, then smaller for second and finish thread with third pass. Always use light oil when cutting threads. $8.60

K&S 4-40 Threading Die  Fits 3/4 inch die handles. Adjustable die. When cutting threads do not try to cut in one pass. Adjust the die to is largest size for first pass, then smaller for second and finish thread with third pass. Always use light oil when cutting threads. $8.60

K&S Die Handle  made for K&S standard and metric dies. Made in USA  $12.00