The Traxxas Spartan Brushless Muscle Boat    $420.00

• 36" deep-V hull for stable high-speed performance
• Water-cooled, waterproof VXL-6s Marine speed control
• 6S LiPo compatible with built-in Low-Voltage Detection
• Velineon 540XL high-output brushless motor with water-cooling jacket
• Blue-anodized aluminum rudder support, rudder, and drive strut
• Stainless steel turn fins, trim tabs, and hardware
• TQ 2.4GHz High-Output radio system with Traxxas Link™
• Includes two 7-cell Power Cell battery packs
• Waterproof high-torque steering servo

Traxxas On Board Digital Temp Gauge  Great for monitoring engine temperature during operation. Large LCD screen. On/Off button for longer battery life. Reads in Celsius and Fahrenheit. RECALL button for highest temperature. Clear splash guard for protection.  $25.00

3674 Water Jacket Machined aluminum jacket with 90 degree fittings. Made for 36x74mm motors that are 36mm diameter (540xl type). Note: Photo is of a 540, this jacket is the same length as the one below.  $12.00

540 XL Water Jacket  Nickle plated with over sized water fittings. 60mm long (2 3/8") for maximum cooling of XL motors that are 36mm diameter.  $12.00

Nylon Shear Bolts  Change the bottom rudder bolt to these nylon shear bolts to protect both rudder and transom from damage. This is the first change you should make. For the Spartan rudder. Pack of 5 for $2.00

Upgrade Shaft Kit  The upgrade shaft kit is a direct bolt on with no mods needed. Kit uses a replaceable floating bushing to improve performance and last longer then the stock setup. Included is a new modified strut, strut bushing and flex shaft with lock-nut. $40.00 per kit

3/16 One Piece Upgrade Shaft  Welded 3/16 flex and 3/16 shaft. Cut to length with soldered end. Includes Locking prop nut. A perfect upgrade but you will need to change from the stock collet and strut.  $20.00

Upgrade Strut and Bushing This is a direct bolt on upgrade strut and floating bushing. Can be used with 3/16 flex or .150 flex.   $25.00

Stainless Sealed Bearings  These are Hi-precision, high rpm double sealed all stainless steel ball bearings. A great way to improve the stock strut for use with stock shaft. Press out the brass inserts and install one of these into each end of strut. Sold in pairs for $15.00

Upgrade Strut w/ Bearings  Stock strut with high rpm stainless double sealed bearings installed. For use with stock flex shaft. $25.00

Replacement Strut Bushings  These are replacement bushings for the stock strut. $5.00 per pair

Nylon Shear Bolts for 5 inch Rudder.  These shear bolts are for the 5 inch rudder listed below. 5pcs $1.00

 5 inch Rudder Offset Base w/ Dual water pickup  Longer then the stock rudder to help with the chine (side to side) walk.
CNC machined aluminum rudder and mounting bracket with dual water pickups and servo arm. Brass bolt for kickback protection.
5 inch (128mm) from bottom of mounting bracket to rudder tip.
3 5/8 inch (94mm) from transom to leading edge of rudder.
Transom foot print is 1.7" (43.4mm) wide and 1.26" (32mm) high.
Rudder width tapers from 1 1/4 inch to 1.1
Servo arm w/ 2mm swivel.  All stainless steel locknuts, bolts and washers included.  $27.00 each

Thick Wall Silicone Tubing   This is the good stuff, will not tear yet very flexible. Has a wall thickness of 2mm.
3mm inside diameter and 7mm outside diameter.  Sold in 3 foot length for $5.25
4mm inside diameter and 8mm outside diameter.  Sold in 3 foot length for $6.50
 

Colors/Sizes

3mm Blue $5.25 USD 3mm Red $5.25 USD 3mm Orange $5.25 USD 3mm Yellow $5.25 USD 3mm Black $5.25 USD 4mm Blue $6.50 USD 4mm Red $6.50 USD 4mm Orange $6.50 USD 4mm Yellow $6.50 USD 4mm Black $6.50 USD

4" Colored Zip Ties   Red, White, Blue, Yellow, Black, Orange. Sold in packs of 25pcs for .75 or 100pcs for $2.50

Quantity

25 pcs $0.75 100 pcs $2.50

Colors

Red White Blue Black Yellow Orange

Transom Mount Water Pickup  Machined aluminum transom water pickup. A nice clean set up only requiring one hole for mounting. 5/32 brass pickup tube. $6.50 each

5/32 Y Fitting    These have a large .110 inside diameter.  You will have to grind or file off the barbs if using with standard size 1/8 id tubing.  $1.50each
 

Medium 68mm Turn Fins Made from .060 (1.5mm) thick aluminum hard anodized to look like chrome. Adjustable depth and angle. Mounting brackets and all hardware included. This is not a direct bolt on for the Spartan, you will have to add another hole to the transom.  $15.00 per pair.

4mm Aluminum Bullet Nut  Hard anodized aluminum. Fits the stock shaft. Has a 4mm thread.  $2.00
 

Color

Silver $2.00 Blue $2.00 Red $2.00

5mm Teflon Washers   Place between the drive dog and strut to prevent wear. Can be used on 3/16 or 5mm shafts. Pack of 10 for $7.50

Teflon Liner for .150 Flex Fits the K&S 1/4 brass tube. Sold by the foot for $2.50

Prather 215    Has a diameter of 1.6" (40.6mm) and a total pitch of 2.5"    Fits a 3/16 shaft.    Made in USA
 

Alloy

B-215 Beryllium Copper $14.95 S-215 Stainless Steel $15.95

Prather 220   Has  diameter of 1.72" (43.7mm) and a total pitch of 2.6"     Fits a 3/16 shaft.    Made in USA

Alloy

B-220 Beryllium Copper $14.95 S-220 Stainless Steel $15.95

440  (40x56)   Diameter of 40mm x 1.4p = 56mm total pitch        Fits 3/16 shaft.  $12.00

442 Back Cut  (42x59)  Diameter of 42mm x 1.4p = 58.8mm total pitch     Fits 3/16 shaft.  $12.00

Traxxas Lipo 3s 11.1v 5000mAh 25c/50c  Traxxas Power Cell 11.1V 6400mAh 25C LiPo 3S Battery with High Current Connector and JST/XH Balance Plug. $79.00

Traxxas Lipo 3s 11.1v 6400mAh 25c/50c  Traxxas Power Cell 11.1V 6400mAh 25C LiPo 3S Battery with High Current Connector and JST/XH Balance Plug. $105.00

Traxxas Lipo 3s 11.1v 8400mAh 25c/50c  Traxxas Power Cell 11.1V 6400mAh 25C LiPo 3S Battery with High Current Connector and JST/XH Balance Plug. $130.00

Traxxas Parallel Connector  $3.15

Traxxas Connectors  Shrouded wire connection, no shrink tube required. Reverse polarity protection makes it impossible to connect backwards. Compatible with high-current 12-gauge wire.  $3.50 Sold in pairs either m/f, m/m or f/f.
 

Type

1 male 1 female $3.50 2 males $3.50 2 females $3.50

Traxxas Charger Lead  Made from quality multi strand 14awg wire.  $3.00 each

Traxxas Series Connector  Connects to lipos in series to double your voltage. Make one 4S pack from two 2s packs.

Vinyl Electrical Hatch seal tape  Colored electrical tape for sealing the hatch is my personal favorite. You can use this tape more then once which is great for testing and setting up when you need to check for leaks and check your temps. 3/4 wide x 66 feet long.  $1.50
 

Colors

Red $1.50 White $1.50 Blue $1.50 Orange $1.50 Yellow $1.50 Green $1.50

Trim Tab Adjusters                  $18.00

Receiver Box Seal Kit      Properly seals receiver box to minimize moisture.  $3.90

Battery Straps  Velcro buckle type straps. 4 pcs per pack.  $5.80

Hatch Post / Water Outlet  Kit contains Hatch Post, Water Outlet, foam pads, washers and screws.  $4.80

Stuffing Tube Seal and Push Rod Seal   Kit has one of each.  $2.00

Turn Fins  Stainless turn fins with mounting screws. One left and one right.  $6.70

Stock 42x59 Prop   $4.30

Body Clip Retainer / Black   4 pcs per pack.  $2.90

Body Clip Retainer / Blue    4 pcs per pack.  $2.90

Body Clip Retainer / Red   4 pcs per pack.   $2.90

Traxxas Body Clips  Pack of 12 clips for $2.00

Rudder / Rudder arm/ Hing pins     $23.50

Rudder Mount / Rudder Pivot  with stainless screws    $15.00

Traxxas Hardware Kit   Stainless Steel nuts and bolts needed for the Spartan.  $11.20

Spartan Drive Strut  Stock replacement drive strut. $9.70

Spartan Drive Strut Mount   $6.70

Spartan Drive Dog  Stock brass replacement drive dog.    $2.90

Spartan Flex Cable  Stock replacement cable and 5mm shaft.  $19.00

Spartan Stuffing Tube w/ Liner   Stock replacement brass tube and liner.   $13.00

Spartan Water Tubing  Stock replacement tubing. 1 meter.   $5.30

Spartan Motor Collet   Stock replacement collet.    $13.00

Rudder Push Rod Assembly   Includes push rod, servo horn, ball links and screws.  $4.50

Radio Tray Retainer        $13.00

Trim Tabs  Stock trim tabs.     $5.80

Spartan Hatch  Replacement hatch. White no graphics. $19.00

Red Spartan Hatch  $26.40

Blue Spartan Hatch   $26.40

Spartan Decal Sheet  Replacement decals. $11.60

Sponsor Decal Sheet  Pressure sensitive, peel and stick vinyl decals. Logos include: Traxxas, Lunati Cams, Hedman Hedders, Simpson, MSD, Mr. Gasket, NOS, Accel, Hurst, and more.  $2.90

Traxxas Team Decal Sheet  Pressure sensitive, peel and stick vinyl decals. Decals include: yellow, black, red, purple and yellow/orange Traxxas logos, Traxxas From Start To Finish (checkered flags) logos, TRX logos, two fuel fillers, four hood pins.  $4.30

Traxxas TQ 2.4GHz High Output Radio System 4 Channel
DSSS (Direct Sequence Spread-Spectrum) 2.4GHz technology
Channel 3 toggle switch and three position channel 4 switch for full compatibility with Traxxas models equipped            with reversing transmissions and T-lock differentials
Traxxas Link automatic model recognition software stores up to 20 previously bound receivers and recalls all           settings when specific receiver is switched on-no juggling of transmitters or scrolling through menus          
        searching for model names
Five channel receiver with two steering outputs for dual servo systems
Multi-function knob can be programmed to control steering exponential steering and braking dual rate and   
         throttle trim
Two button "menu" and "set" interface
Steering and throttle end point adjustment, servo reversing and sub trim adjustment
13ms frame rate and 4-17ms latency for instant steering and throttle response and precise, smooth control
Thirty day limited warranty through manufacturer beginning at date of purchase.    $103.00

 

Receiver Micro TQ 2.4GHz  5 Channel     $39.00