Bolt on Trim Tab Adjusters w/ Water pickup. No need to drill new holes. All you need is an allen wrench to install. Makes dialing in your tabs much easier and more accurately especially when water conditions keep changing. The pickup will increase water flow approx 3 times over original rudder pickup. All stainless steel hardware w/ brass pickup included. Made from blue anodized aluminum. Natural finish aluminum is available.         $25.00 per set           Made in USA.
    

Finish

Blue $25.00 Natural $25.00 pickup tube only $1.00

SV27 Latch upgrade. If you cant stand the leaky rusty factory unit, then this is your answer. Finger tight makes a watertight seal. The small o-ring holds the bolt in place when doing maintence. Everything needed included.      Made in USA. $7.50

540 Super Cooler Water Jackets   These jackets are the longest jackets on the market. In both 540S and 540XL sizes. Each jacket has 4 holes for better water line placement to make the cleanest and most efficient layout of your interior. Ribbed to dissipate heat quicker. High flow fittings for better water flow. Each jacket comes with 4 sealing o-rings(2 spare), High flow 90deg and straight fittings, jam nuts to adjust line direction, o-rings for the fittings, dummy caps to seal the unused holes. Pictured with a 540XL on a Nemesis XL and a 540S on a SV27 motor.  Without question the best made jackets on the market. Guaranteed to put a smile on your face. Another quality Kintec Racing product. Made in USA.
  

Colors and Sizes

540 S Blue $25.00 540 S Red $25.00 540 XL Blue $27.00 540 XL Red $27.00

Touch Up Paint    After many trips all over town I found the closest matching colors for the factory paint. 2/3-1 OZ bottles.
 

Colors

Red $3.75 White $3.75 Blue $3.75 Orange $3.75 Green $3.75 Yellow $3.75

Water Jacket  Beautifully machined aluminum water jacket. Threaded hose fittings that wont come loose like the glued in competitions not to mention the much larger hole size. Improves water flow and surrounds the whole motor for much better cooling which makes the motor run better and last longer. Fits any 540 size motor. 36mm ID x 44mm long.    $16ea

PORT SIDE TURN FIN  A must have for sport running or turning left.      $17.00

LipoShield  Intelligent Lithium Cutoff, 1-12s, Soft cutoff. Works with all ESCs. These have been reprogrammed to cutoff at 3.3volt per cell. Now you can run lipos in your supervee with the stock ESC and not damage or shorten the life of your lipos. Just run till the cutoff kicks in, go to zero throttle and bring her in. No more need for a stop watch or worrying how much juice you have left. For the price this is a must have if you are running lipos. A great backup for any ESC. If you cant solder get the pre installed Deans option. This also allows you to move the unit from one boat to another.     Made in USA  
     

options

Lipo Shield $20.00 With Deans $35.00

Antenna Mount   Here is the answer to the leaking stock antenna tube. Beautifully machined aluminum. Mount on the hatch for a water tight seal or drill a 1/4 hole above the transom for a leak proof no hassle mount. Far superior to anything on the market.  Machined aluminum. Mount the o-ring on the inside to make a secure and shock absorbing mount. Made in USA   $4.75 ea

        

Collet   5mm X .150inch   With out question the best collet on the market. Three piece design for slip proof ultra secure grip by just snugging up the wrenches. High precision machined stainless steel with a brass insert. You can not strip or split this like the stock collet or the octura 2 piece units. Not only will this hold better it will increase the life of your flex shaft. The brass inserts are replaceable if you would ever wear it out so no need to buy the whole unit a second time.   Made in USA  $16.00

Collet 5mm x .150

3 pc collet $16.00 .150 insert only $6.50

Servo Mount  Radio box replacement. After you get your boat nice and water tight you might want to replace the big bulky radio box. Made from 1/8 inch HARD wood not balsa. Precision pre-cut and drilled for a no hassle installation. The servo box will be in the proper location and no need to readjust your linkage. All stainless screws and aluminum servo mount provided. This makes your boat so much easier to work on especially when loosening your collet. An added bonus is you will loose a full 2 ounces of weight. Less weight means MORE SPEED.  Another quality Kintec Racing product.   Made in USA  $12.00

Thrust Bearing  For any motor with 5mm shaft. Helps prevent wear on motor bearings. Mount between motor and collet.   $7.65ea
Note: A spacer is needed for the SV27 motor. Spacer is made to be used with any collet and reduce vibration caused by washers.
     

Options

Bearing only $7.65 Spacer only $3.50 Bearing and Spacer $11.15

Supervee 27 Bullet Nut.  The only bullet nut made for the stock SV27. Made from solid brass or stainless which is much stronger then aluminum and will not flake or rust like the plated ones. These can be polished to a super high luster. Photographed raw. This makes the boat look so much better and faster.  Made in USA.
        

Materials

Brass 4mm $3.45 Stainless 4mm $4.45 Option 3 $3.45

AMMO Brushless motor.   36-50-2300kv  This is the motor GrimRacer recommends as an upgrade. No changes to your
electronics required.  $69.00
 

AMMO  Water Jacket   Ammo motors are slightly larger then the stock 540 motor so this is the jacket you need if you are upgrading your motor. Do your homework this jacket works so well it has already been copied but still not up to par with this unit. Now available with the only HIGH FLOW 90degree fittings on the market.             Another quality Kintec Racing product.  $15.00ea       Made in USA
 

Fitting options

Jacket w/ straight fittings $15.00 Jacket w/ 90deg fittings $19.00

Nylon Screw Set    A good way to prevent damage to your rudder and keep your transome from cracking is to add a nylon breakaway screw. A quick and easy fix. 6 screws and 6 nuts per set.
 

Hatch Seal Tape. This is probably the most popular tape for sealing up your hatch. Makes a nice watertight seal. Leaves no residue and will not pull your decals when removing.   1 inch wide X 100 feet long.      $2.95 per roll
 

Colored Hatch Seal Tape  Colored electrical tape for sealing the hatch is my personal favorite. You can use this tape more then once which is great for testing and setting up when you need to check for leaks and check your temps. 3/4 wide x 50 feet long.
 

Colors

Orange $2.50 Yellow $2.50 Blue $2.50 White $2.50 Red $2.50 Green $2.50

Aquacraft 3 blade 40mm.  Part# AQUB7888. This is the stock prop that comes with your boat. A good sport running prop and not to hard on your wallet. Sold in pairs for $16.50
 

GrimRacer 40 X 52/3  Aquacraft# AQUB9720   High performance Copper-Beryllium-Titanium.  These props are impressive. Very well made with no flashing and tumbled to a bright finish. If you don't know how to balance a prop these are as close as you can get. Very close in and pitch as the octura 440/3.      Made in USA  $19.95 ea
 

Grim Racer 42-55  #AQUB9725    This is the prop Grim Racer recommends for top end speed. According to the Aquacraft chart it is the replacement for a Prather 230 but it has a radius on the tip where the Prather is more pointed. Made in USA   $20.95ea
 

Octura X642  This is a 2 blade Beryllium Copper prop. Great hole shot prop that throws a big rooster tail and gets on plain fast. A really good short corse prop. Diameter of 1.65" (41.91mm)  pitch of 2.64" (67mm)  $13.00 ea
 

Octura X437/3  Beryllium Copper prop.    Diameter of 1.48" (37.59mm)  pitch is 2.072" (52.63mm)       Fits 3/16 shaft.          14.50ea
This prop was the points champion in the sv27 class in 2008 on the west coast.
 

Octura X440/3   This is a 3 blade Beryllium Copper prop. This is the prop that I prefer for max top end speed.

Prather 215   Another great hole shot small coarse prop. Has a diameter of 1.6" and a pith of 2.5"   These props are very well made with no mold flashing which makes for easy balancing. This prop produces good speed and runs a bit cooler.  Made in USA

Alloy

B-215 Beryllium Copper $14.95 S-215 Stainless Steel $15.95

Prather 220  Might just be my new favorite prop. Has  diameter of 1.72" and a pitch of 2.6"   Very well made. Provides monster hole shots and big rooster tails, this is a real crowd pleaser. Watch your temps with this one. It will heat things up and I do not recommend it if you are using cheap or old batts/lipos.   Made in USA

Alloy

B-220 Beryllium Copper $14.95 S-220 Stainless Steel $15.95

Prather 230   Diameter of 1.9" and a pitch of 3.0"  If you have an upgrade motor then this ones for you.   Made in USA

Alloy

B-230 Beryllium Copper $15.00 S-230 Stainless Steel $16.95 Option 3 $15.00

Prop Balancer  This is without question the best prop balencer on the market. Can be used on any surface and does not need to be leveled. Will even work if you hold it in your hand. All other balencers that use cones need balanced. Why buy a balencer that needs balanced? Beautiful machined aluminum brackets with hardened tool steel shafts for a no wear no bend unit. Another quality Kintec Racing product. Made in USA  $35.00

 

Prop Balancer & shafts

3/16 Balancer $35.00 1/8 & 3/16 Balancer $40.00 1/4 Balancer $45.00 3/16 & 1/4 Balancer $50.00 1/8, 3/16, 1/4 Balancer $55.00 1/8 shaft only $7.00 3/16 shaft only $9.00

SV27 Rudder  Aquacraft part# AQUB7880   Rudder blade with set screws and water fitting.  If your going to make an order might want to add one of these. I snap at least 2 per year and always nice to have a spare.  $21.40 ea

Prop Shaft Bushing  AQUB7884  Every once in a while you need to replace the bushing, they do wear.  $9.90 ea

Prop Shaft with Flex Cable  #AQUB7883  Assembled flex cable and prop shaft with prop nut.  $12.90 ea

 

Drive Dog   AQUB7885    Drive dog with prop nut for 3/16 shaft. Very small 8mm OD.  $7.95ea

Cowl Hatch    Aquacraft #    AQUB6201   $21.50 ea

Colors

White AQUB6201 $21.50 Blue AQUB6202 $21.50 Red AQUB6203 $21.50 Yellow AQUB6204 $21.50 Green AQUB6205 $21.50 Orange AQUB6206 $21.50

Velcro One-Wrap straps  1 inch wide x 8 inches long. A great way to hold down your Lipos or batts.    4 straps for $3.

 

3M Velcro.  This is industrial strength Velcro brand velcro with adhesive back. This is the strongest adhesive Velcro makes (blue label). Very strong. If you have removed your wood battery trays then this is a great way to keep the lipos or batts in place. Once you know where you want your batts just stick the hook side to your hull and the loop side to your lipos and your good to go. Sold by the foot in 1 or 2 inch width.
             

Sizes x 1 foot

1" hook & loop $1.65 1" loop only (lipo side) $0.85 2" hook & loop $2.75 2" loop only (lipo side) $1.40

Dubro Antenna Caps  These help keep that little bit of water out when you put the boat on its lid. Comes with 2 caps and 2 silicone antenna retaining collars.
 

Dubro Colored Antenna Tubes   Add a colored tube to match your hull or your stripes. You would be surprised how much different they make the boat look
  

Colors

White $0.75 Red $0.75 Green $0.75 Orange $0.75 Blue $0.75 Yellow $0.75

Brushless Decals  Listed by Hull Color
                                                                                                                        

                                     WHITE                                                                BLUE                                                                         RED
        

                               GREEN                                                             YELLOW                                                                     ORANGE 
     
  

Hull Color

White $11.00 Blue $11.00 Green $11.00 Yellow $11.00 Orange $11.00