KINTEC RACING
Precision Perfomance Products
Thick Wall Silicone Tubing This is the good stuff, will not tear yet very flexible and hard to kink. Has a wall thickness of 2mm.
3mm inside diameter and 7mm outside diameter. Sold in 3 foot length for $5.25
4mm inside diameter and 8mm outside diameter. Sold in 3 foot length for $6.50
4" Colored Zip Ties Red, White, Blue, Yellow, Black, Orange. Sold in packs of 25pcs for .75 or 100pcs for $2.50
Great Planes 3/32 (2mm) Line Clamps Spring steel clips for use on 3mm white or smaller lines.
4pcs for $1.20
Great Planes 5/32 (3mm) Line Clamps Spring steel clips for use on 3mm colored or 4mm white line. Will not work on 4mm colored line. 4pcs for $1.30
1/4 Stainless Steel Tube Clamps Stainless clamps for use on 1/4 od tubing. Works well on 4mm white or 3mm colored tubing. .30cents each
5/16 Stainless Steel Tube Clamps Stainless clamps for use on 4mm colored tubing. .30 cents each
Water Jacket Replacement O-Rings These rubber o-rings are stronger then the silicone o-rings and are also oil resistant which make oiling a jacket for easy install. Listed by width of ring and motor diameter. 1 each.
540 Super Cooler Water Jackets These jackets are the longest jackets on the market. In both 540S and 540XL sizes. Each jacket has 4 holes for better water line placement to make the cleanest and most efficient layout of your interior. Ribbed to dissipate heat quicker. High flow fittings for better water flow. Each jacket comes with 4 sealing o-rings(2 spare), High flow 90deg and straight fittings, jam nuts to adjust line direction, o-rings for the fittings, dummy caps to seal the unused holes. Pictured with a 540XL on a Nemesis XL and a 540S on a SV27 motor. Without question the best made jackets on the market. Guaranteed to put a smile on your face. Another quality Kintec Racing product. Made in USA.
UL-1 Super Cooler 1.75OD X 2" long. This is the top of the line water jacket for the UL-1. Four holes for universal placement of cooling lines. The jacket covers just about the entire motor for maximum cooling. Comes with nickle plated fully adjustable banjo fittings and blind plugs for the holes not in use. Ribbed for her pleasure.
UL-1/AMMO Low Profile Water Jacket Since most of the stock water jackets leak we made an upgrade that is easy to install. This jacket has the smallest od of any jacket on the market yet has a larger inside dia. Do your homework this jacket has already been copied but still not up to par with this unit. Now available with the only HIGH FLOW 90degree fittings on the market. Another quality Kintec product. $15.00ea Made in USA
540 Water Jacket Beautifully machined aluminum water jacket. Threaded hose fittings that wont come loose. Fits most 540 size motors. 36mm ID x 44mm long. Spare o-rings included. $13ea
540 Water Jacket Nickel plated with larger brass nozzles then the black counterpart. To shinny to get a good picture. 45mm long (1 3/4")
Works with most 540 size (36mm diameter) motors. $10.00ea
540 XL Water Jacket Nickle plated with over sized water fittings. 60mm long (2 3/8") for maximum cooling of XL motors that are 36mm diameter. $12.00
40mm Water Jacket Anodized aluminum jacket for 40mm diameter motors. 50mm long. $12.00
380 Water Jacket Beautifully machined blue anodized aluminum. 28mm ID X 36mm long. Comes with 2 spare o-rings.
36mm-45mm Silicone Jacket Fits motors from 36mm-45mm diameter. Large 5/32 fittings. Nice jacket to have around since it will fit any standard 540 motor, Ammo, Aquacraft, Leopard, and other 600 size motors.
1 5/8 (43mm) long. $8.00
28mm Silicone Jacket Fits motors with a can diameter of 28mm. Length is 1.4" (36mm) not counting the outlets. $8.00 each
Motley Crew / UL-1 / SV27R Water Jacket Aquacrafts new anodized aluminum water jacket for their 1800kv and 2050kv motors. Has 8 positions for the water fittings for better line positioning. $6.30 each
Inline Cooler Place these inline between the esc and motor. Reduces water temp from esc before entering motor. 3/8 (10mm) diameter and 2 1/2 (63mm) long. $7.00 ea
Small Inline Cooler Place these inline between the esc and motor. reduces water temp from esc before entering the motor. 3/8 (10mm) diameter and 1 1/8 (29mm) long. $6.50 each
Dual Transom Mount Water Pickup Machined aluminum with brass fittings. Easier to install then through hull units yet works the same. Comes with stainless hardware.
.8"long from transom(20mm), .84" wide (21mm), .97" high (24.5mm) $7.00 each
Transom Mount Water Pickup Machined aluminum transom water pickup. A nice clean set up only requiring one hole for mounting. 5/32 brass pickup tube. $6.50 each
Transom Mount Water Pickup Machined aluminum transom water pickup. A nice clean set up only requiring one hole for mounting. 5/32 brass pickup tube. Comes with aluminum feral for water line and 2 feet of 1/8 silicone water line. Imported. $10.00
Transom Water Pickup AQUB9045 Nice compact single screw transom mount pickup for use with 1/8 line.
Grimracer Transom Pickup Bolts threw the hull. Everything needed included. For 1/8 line. $7.30
Through Hull Water Pickup Mounts on the floor of hull. Very easy to install, just drill a hole and epoxy in. Nice large inside diameter of .150 inch (3.8mm). $1.75 ea
Flush Mount Water Pickup Mounts on the floor of the hull. Nickle plated aluminum. $3.50 ea
Dual Flush Mount Water Pickup
6mm Through Hull Ring Plated aluminum dress up ring. Has a 6mm (2.36") inside diameter. These are a perfect fit for the Aquacraft blue and green line. $2.00 each
6.8mm Through Hull Ring Plated aluminum dress up ring. Has a 6.8mm (.268") inside diameter. $2.00 each
Banjo Fittings Low profile, fully adjustable in any direction, Nickel plated, 10 x 32 thread. $5.00 each
90 Degree High Flow Water Fittings Since there are no high flow 90 degree micro fittings in any industry Kintec answers the demand. Soon to be the standard in boat fittings these are made with you in mind. Fully adjustable to point in any direction. Small and compact made of brass and comes with fitted o-rings. 10-32 thread. $8.00 per pair.
1/8 Y Fitting This is the standard Y fitting for 1/8 or 3mm line. Inside diameter is .095 $1.25 ea
5/32 Y Fitting High Volume for 1/8 or 3mm line. These have a large .110 inside diameter. These fit our 3mm tubing just fine but you might have to grind or file off the barbs if using with other brand 1/8 id tubing. $1.50each
3/16 Y Fitting Perfect for use in our 4mm lines. Has a large .128 inside diameter. Can be squeezed into our 3mm line if barbs are removed. $1.65 each
Aluminum Y Fitting Small Works great with 3mm (1/8) or larger tubing. $3.00 each
Aluminum Y Fitting Good for 3mm (1/8) tubing and larger. $4.00 each
1/8 T Fitting These are the standard T fitting for 1/8 or 3mm line. $1.00 each
5/32 Tee Fitting These are for high flow in 1/8 or 3mm line. $1.00
3/16 Tee Fitting For use with our 4mm line. $1.00 each
Aluminum T Fitting Good for 3mm (1/8) tubing and larger. $4.00 each
Aquacraft Water Outlet AQUB9519
Standard Size Water Outlet machined aluminum with nut and o-ring. For use on 1/8 and 3mm tubing. $2.50
LG Bore Water Outlet Machined aluminum with stainless nut and rubber washer. Fits 3mm or 4mm tubing.
.135 ID, 1/4 thread Made in USA $2.90
Large Water Outlet Machined Aluminum with nut and o-ring. Use with 4mm up to 1/4 tubing. $2.90
Standard Size Transom Fitting Machined aluminum with nut and o-ring.
Transom Fitting Large 1/8 Inside diameter. Made from Aluminum. Makes for an attractive functional install of cooling lines.
5mm Banjo Fitting Fully adjustable to point in any direction with a 5mm thread. Nickle plated aluminum.
$4.50 each
Fitting 4mm Thread Aluminum water fitting with a 4mm thread. 15mm long. $1.50 each
Fitting 5mm Thread Brass water fitting with a 5mm thread .16mm long. $1.50 each
6mm Fitting Brass water fitting with a 6mm thread. $1.50 each
6mm High Flow 90 Degree High flow fitting with a 6mm thread. $1.00 each
Aquacraft Blue Tubing 3 feet of silicone tubing
Aquacraft Green Fuel Tubing 3 feet of glow fuel tubing. Inner diameter is 3/32 and outer diameter is 3/16.
3mm x 5mm Silicone Water Line Has an inside diameter of 3mm (1/8") and outside dia of 5mm (.197")
Sold in 3 foot lengths for $2.00
4mm x 7mm Silicone Water Line Has an inside diameter of 4mm (5/32") and outside dia of 7mm (.276")
Sold in 3 foot lengths for $2.00
K&S Brass Tubing 1/8 #127 1/8od x .014wall (3.18mm x .355mm) A great size for water pickups or silicone tubing connectors. Sold in 1 foot lengths for $1.00
1/8 Line Barb These line barbs can easily be added to 1/8 k&s brass tubing by either soldering or using loctite.
4 solid brass barbs per pack for $1.60
K&S Brass tubing 5/32 #128 5/32od x .014wall (3.97mm x .355mm) Perfect for water pickups. 1/8 water line fits snugly without the need for zip ties. Also works great for threw hull fitting. Makes a great silicone tube connector. Used on all Kintec racing water pickups. Sold in 1 foot lengths for $1.15
5/32 Line Barbs These line barbs can easily be added to 5/32 OD tubing by either soldering or using loctite.
4 solid brass barbs per pack for $1.90
Water Cooled Motor Mount 380-540 Machined aluminum motor mount with G10 side plates. Fits 380-540 sized motors. All stainless hardware included. $14.50
Carbon Fiber Water Cooled 540XL Motor Mount Aluminum water cooled motor mount with carbon fiber side plates. Has rear support for L and XL motors. Fits 540 sized motors. 3 5/8 inch (92mm) long. $23.00 ea
40mm Motor Mount Aluminum water cooled motor mount. Fits motor with a 40mm diameter can. Total length is 100mm (3.93") Width is 58mm (2.28") $20.00
40mm Carbon Fiber Motor Mount Aluminum water cooled motor mount with carbon fiber side plates. Fits motors with a 40mm diameter can. Total length is 100mm (3.93") Width is 58mm (2.28") $25.00
